General Fitment

Würth exhaust assembly paste is perfect for sealing flanges and slip-fit joints; withstands 700-degrees; hardens with exhaust heat. 5oz. Tube. From Germany.

General Fitment

We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)

Cv boots are inexpensive, so replace them before they crack and cause an expensive cv joint failure. This kit does one side, two needed per axle.

General Fitment

A good upgrade for slightly modified engines. Convert fuel injected 2.0 engines to weber 40 mm (40 idf) dual throat carbs. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. This kit is for off-road and racing use only, and must never be used on the highways in california. When switching from fuel injection to carburetors, each kits require a lower-pressure fuel pump (part number run7...(choose a part on the right to read more)

General Fitment

We deliver with dmsb-ons certificat ,incl. Tunneling supporting and diagonal bars for the work location motorsport you need this options: 600001 side rotection 600035 dash board panel faces optional : 600036 harness mounting tube only in steel 600006 upholstery 600014 diagonals bars with connecting joint every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request exp...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport ...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Black paint finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold al...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. Chromoly steel 1.5 inch diameter tubing, .098 wall thickness tubing. A true bolt in bar that does not require drilling or welding. Includes a harness bar which is located on the b-pillar hoop. Bars which connect to the main hoop, use a connecting joint system so that you can easily access the motor without the use of tools. Tig welded. Retains full seat adjustability. Factory seat belts or 5-6 point belts can be used. Semi-gloss black finish. The front hoop mounts to the upper bulkhead, in the OEM m...(choose a part on the right to read more)

Made of carbon. Polished titanium joints. Magnesium wheels with Porsche crest. Attachment for scorecard holder and umbrella holder. Trolley bag in black. Dimensions (assembled): 72 (track) x 126.5 (max. Length) cm. Dimensions (stowed in trolley bag): 18 (l) x 64 (w) x 33 (h) cm. Golf bag (wap 060 041 17) can be easily and securely mounted on the trolley using the adapter set (wap 060 046 19).

General Fitment

Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)

If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stoc...(choose a part on the right to read more)

Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad

The bbi autosport Porsche 996 & 997 streetcup roll bar features a 2-piece design and 4130 chrome moly steel tubing (1.5" x .120" main hoop & 1.5" x 0.95" rear hoops) for excellent strength to weight ratio. Taking a sensible design approach, the 2-piece construction allows the bar to be mounted to the front seat belt mounts and to the rear strut towers (stronger mounting points), and still be compatible with the factory bose subwoofers. Other similar roll bars on the market are not compatible with the subwoofer. For superior strength and rigidity, the bar utilizes "x" braces on both front and rear sections and each joint has been meticulously tig welded by hand. Bolt-in installation is accomplished by usin...(choose a part on the right to read more)

- 2 3/4 tubing (70mm). - weighs 7 lbs. (3,1 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "quad" style tips, inner tip is 3.5" (90 mm) in diameter and outer is 3.4" (88 mm). - polished stainless steel. - made in Germany - will not fit stock mufflers! These tips only work in conjunction with our "brombacher" sport mufflers. Please note: using stock tips on our sport mufflers without these tips will cause hp loss. Once you restrict the diameter of the piping a small percentage of power is robbed. The exhaust tips are a dual 3.5"/ 3.4 round design and are double walled to dissipate heat, which means that they won't tarnish as quickly as single walled tips. There is an ...(choose a part on the right to read more)

If you are doing sheet metal repair to your Porsche (or any car, for that matter), wurth seam sealer is a must-have. It is used to seals seams & joints that are spot welded, riveted, or bolted. permanent adhesion to bare or painted surfaces. Brush able, low odor formula goes on thick to seal completely, and provides an OEM appearance when finished. Will not sag, shrink, or crack, and is paint-ready in 45 minutes. Temperature range from -13ºf to +176ºf.

General Fitment

Known as: joint

View/Change Diagram

911 1970-73 - Body	912 1965-69 - Body
911 1965-69 - Body

+ 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)

Known as: washer 8 / washer only together with ball joint 911.341.049.01 / washer a 8.4
Known as: washer 8 din 1440-st verz.

View/Change Diagram

356 1960-65 - Fuel/Exhaust	911 1970-73 - Front Axle/Steering
911 1974-77 - Front Axle/Steering	911 1978-83 - Front Axle/Steering
911 1984-86 - Front Axle/Steering	911 1984-86 - Body
911 1984-86 - Body	911 1984-86 - Body
911 1987-89 - Front Axle/Steering	930 1975-77 - Front Axle/Steering
912 1965-69 - Fuel/Exhaust	912 1965-69 - Front Axle/Steering
928 1978-82 - Pedal System/Levers	928 1978-82 - Electrical
928 1983-86 - Pedal System/Levers	928 1983-86 - Electrical
928 1987-91 - Pedal System/Levers	928 1992-95 - Pedal System/Levers

Redline oil: red line formulates fully-synthetic oils and chemically-advanced additives using the world’s finest base stocks. Rather than cutting costs by blending in petroleum products, red line's motor oils and gear oils use superior ester base stocks that provide extreme stability at high temperatures and superior film strength at lower viscosities where more power can be produced.

Volume: 14oz tube redline cv-2 grease withstands extreme temperature and pressure in wheel bearings, u-joints, and high-angle cv joints

General Fitment

General Fitment

Known as: joint flange

View/Change Diagram

912 1965-69 - Transmission	912 1965-69 - Rear Axle
911 1965-69 - Transmission	911 1965-69 - Rear Axle

Known as: joint flange -loebro for chilled casting / joint flange -loebro / joint flange

View/Change Diagram

911 1970-73 - Transmission	911 1970-73 - Transmission
912 1965-69 - Transmission	911 1965-69 - Transmission